Products

TIMER MODULES

  • DL-10 (Timer Module – 10A) and DL-20 (Timer Module – 20A)

Poly Electronics Timer Modules are used in series with most types of lighting or other electronic devices. Poly Electronics Timer Modules help prevent unintentional battery discharge when a light/device are left on for an extended period of time, as when an operator forgets to turn it off. This light-weight unit is small in size and can easily be hidden from view. It is also a cost-effective solution to a very costly problem of damaged or dead batteries. Timers are available in both 10 Amp and 20 Amp versions.

  • DLM-10 (Motion Timer Module – 10A)

Poly Electronics Motion Sensor Timer is used in series with most types of lighting or other electronic devices. When wired to an ignition circuit, it will be powered when the ignition is on. When it senses motion in its vicinity, it will turn on the lighting/device and keep it on for the requested amount of time. As long as motion is sensed, the light/device will stay on. The LED will indicate that motion is being sensed and the timing will be continually reset. Once motion is no longer detected, and ten minutes’ pass, the light/device will shut off. The sensor will continue to monitor for motion.

     

    • 3150

    Poly Electronics Door Open Flasher module was design to flash the rear taillights to warn that there is a door open. It takes the place of a loose flasher, relay, diode block, fuse, and all the wiring, terminals and labor needed to install them. Connections are made though a 6-pin Molex socket.

    DOOR OPEN FLASHER

    BATTERY SEPARATOR

    • 3658

    Poly Electronics Battery Separator is designed for use in multi-battery applications, allowing the primary and auxiliary batteries to be charged. Our Bi-Directional Battery Separator is able to have two charge sources connected; one upon the Main Battery, and a second upon the Auxiliary Battery – This means that the charge current can go in two different directions, from the Main Battery to the Auxiliary Battery, or the Auxiliary Battery to the Main Battery.

    POTTING ENCLOSURES

    • Polyshells

    Poly Electronics stocks a wide variety of plastic potting box’s.

    TIMER MODULES

    • TM-10 (Timer Module – 10A) and TM-20 (Timer Module – 20A)

    Poly Electronics Timer Modules are used in series with most types of lighting or other electronic devices. Poly Electronics Timer Modules help prevent unintentional battery discharge when a light/device are left on for an extended period of time, as when an operator forgets to turn it off. This light-weight unit is small in size and can easily be hidden from view. It is also a cost-effective solution to a very costly problem of damaged or dead batteries. Timers are available in both 10 Amp and 20 Amp versions.

    • MTM-10 (Motion Timer Module – 10A)

    Poly Electronics Motion Sensor Timer is used in series with most types of lighting or other electronic devices. When wired to an ignition circuit, it will be powered when the ignition is on. When it senses motion in its vicinity, it will turn on the lighting/device and keep it on for the requested amount of time. As long as motion is sensed, the light/device will stay on. The LED will indicate that motion is being sensed and the timing will be continually reset. Once motion is no longer detected, and ten minutes’ pass, the light/device will shut off. The sensor will continue to monitor for motion.

    • ODTM-25 (On Delay Timer Module – 25A)

    Poly Electronics On Delay Timer will delay the energizing of a load once power is applied. A convenient knob will allow adjustment of the delay from 6 to 60 seconds.

    Other ranges of time delay as well as various DC and AC operating voltages are available upon request. It is very compact (2″ square) and is encapsulated for durability.

    This timer would be useful for delaying the startup of a component after a brief power interruption. Applications for these timers include but are not limited to OEM products, machine controls, relays, valves, solenoids, lights, motors, contactors for heavier loads and countless other uses.

    • OFDTM-25 (Off Delay Timer Module – 25A)

    Poly Electronics Off Delay Timer will delay de-energizing of a load Upon closure of a normally open isolated start switch. When the switch is opened, the timing starts. At the end of the preset time delay, the output is de-energized and the timer is now ready for a new cycle.

    TAIL LIGHT ADAPTERS

    Poly Electronics taillight adapters provide the proper connection for trailer lights from automobiles and light trucks. Most vehicles now have separate bulbs or filaments in the taillights for Turn Signals, Running Lights, and Stop Lights. Most trailers have two bulbs or filaments, one for Running Light, and one combined for Turn Signal, and Stop Light (each side). To make this combination of lights work correctly, this adapter is necessary. 

    • ND-7

    Poly Electronics ND-7 Taillight adapter is the basic unit that will adapt the 3 light (tow vehicle) to 2 light (trailer). The sturdy construction employs relays – on either side, which makes it much more reliable than the fragile all solid-state units. And unlike solid-state only units, these have minimal heat buildup.

    • HD-7

    Poly Electronics HD-7 Taillight Adapter has the additional feature of direct ‘hot’ line connection for power. This model is recommended for use on tow vehicles where access to a ‘hot’ line is unavailable, thus eliminating the need for an additional heavy-duty flasher. With this unit, full voltage is supplied to the lamps. Meaning, no voltage drops and no dimming of lights!

    WHEEL CHAIR WARNING MODULE

    • 3106

    Poly Electronics 3106 Wheelchair Warning Module eliminates all the wiring and labor needed to install several loose components once your wheelchair lift and logic board are in place. Our 3106 module includes warning buzzer, a flasher for the taillights, a relay, a block diode for wiring protection, and a fuse holder all in one small package. Connections are made though a 9-pin Molex socket.

    • 3107

    Poly Electronics 3107 Wheelchair Warning Module shares the same features as the 3106 module minus the relay.

    DOOR OPEN FLASHER

    • 3150

    Poly Electronics Door Open Flasher module was design to flash the rear taillights to warn that there is a door open. It takes the place of a loose flasher, relay, diode block, fuse, and all the wiring, terminals and labor needed to install them. Connections are made though a 6-pin Molex socket.

    BATTERY SEPARATOR

    • 3658

    Poly Electronics Battery Separator is designed for use in multi-battery applications, allowing the primary and auxiliary batteries to be charged. Our Bi-Directional Battery Separator is able to have two charge sources connected; one upon the Main Battery, and a second upon the Auxiliary Battery – This means that the charge current can go in two different directions, from the Main Battery to the Auxiliary Battery, or the Auxiliary Battery to the Main Battery.

    HVAC

    • 3158

    Poly Electronics Air+ is designed to control the heating and air conditioning APU’s for truck systems. The Air+ features a two-digit display for temperature with push buttons for adjusting the temperature set point, fan speed, and climate mode. The Air+ also has relay outputs so that the loads can be driven directly without the need for an additional relay board. All connections are made through an eight-pin connector that may be plugged directly into a wiring harness.

    POTTING ENCLOSURES

    • Polyshells

    Poly Electronics stocks a wide variety of plastic potting box’s.

    Contact us for more product information